Digi CM User's Guide Page 49
- Page / 158
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Configuring Ports
Chapter 4 49
mode configuration page in the web interface to select the correct protocol.
Serial Port Parameters
In attaching a serial device to a Digi CM serial port, the port parameters must
match. The serial ports by default are enabled, meaning you have full access
to the port. To configure the port parameters for the Digi CM, do the following:
1. Access the web interface.
2. Under the Serial Port heading, Click Configuration.
3. Choose All or an Individual port > Serial port parameters.
4. Fill in the serial port parameters. The following are the defaults: bps=9600,
data bits=8, parity=none, stop bits=1, flow control=none, and DTR
behavior=High when open.
5. Click Save & apply
DTR Behavior
DTR can be set on the serial port to one of three settings: always high, always
low, or High when open. Setting the DTR to High when open keeps the DTR
high if a TCP connection is established. The DTR setting cannot be set by you
when the host mode is configured for dial-in modem or dial-in terminal server
mode.
Inter-character Timeout
This setting is only available when the host mode protocol is set for RawTCP.
The parameter sets the time value for the Digi CM to transfer data stored in the
buffer. The Digi CM transfers data when the buffer is full using the TCP/IP
protocol. However, if it is not full, the Digi CM will also transfer data dependent
on the timeout value selected.
- Digi CM 1
- Contents 5
- 6 Contents 6
- 8 Contents 8
- Introduction 9
- Feature Summary 10
- Chapter 1 10
- Web Interface 11
- Configuration Menu 12
- 14 Chapter 1 14
- Port Escape Menu 18
- CISCO.Router.port3 19
- Sun.nemo.port5 19
- 20 Chapter 1 20
- Getting Started 21
- 22 Chapter 2 22
- The Digi CM 23
- Configuring a Port for SSH 24
- Procedure 25
- About Shell Options 26
- Digi CM 32 show 27
- Chapter 3 31 31
- Adding a Serial Modem 32
- Chapter 3 32
- System and Port Logging 33
- Enable SYSLOG Server 34
- Enable A Compact-flash Card 35
- Enable Digi CM Memory 36
- Viewing System Logs 37
- Chapter 5 39 39
- 5. Click Save & apply 39
- Viewing Port Logs 40
- Configuring Ports 41
- 42 Chapter 4 42
- Serial port parameters 42
- Console Server Mode 44
- Terminal Server Mode 45
- Dial-In Modem Mode 46
- Dial-In Terminal Server 46
- SSH, Raw TCP, and 48
- DTR Behavior 49
- Inter-character Timeout 49
- Serial Port Parameters 50
- Chapter 4 50
- Alerts and Notifications 51
- 56 Chapter 5 56
- Port logging 56
- Port event handling 56
- User Administration 59
- Administering Users 60
- Chapter 6 60
- 4. Click Apply changes 60
- 192.168.1.108 61
- Filter IP: 192.168.1.0 61
- Filter Mask: 255.255.255.0 61
- 192.168.5.10 61
- Chain rule 63
- 64 Chapter 7 64
- Chapter 7 65 65
- • or restrict rights to Jeff 65
- Sniff Session 66
- Permit monitor only mode 67
- Authentication 67
- 68 Chapter 7 68
- Custom and Default Menus 69
- Creating Menu Names 70
- Adding Menu Items 71
- Assigning Users to a Menu 72
- Default Menu 74
- Chapter 8 74
- Microsoft SAC Support 75
- Command Syntax 76
- Command Example 76
- 78 Chapter 9 78
- Chapter 9 79 79
- Field Description 79
- Chapter 9 80
- Host mode configuration 81
- 82 Chapter 10 82
- Assign a port name: 82
- Chapter 10 83 83
- Chapter 10 84
- 86 Chapter 11 86
- 88 Chapter 11 88
- Chapter 11 90
- Add the power controller 93
- 98 Chapter 12 98
- 100 Chapter 12 100
- Power Controller 101
- Chapter 12 101 101
- Chapter 12 102
- Port Clustering 103
- 104 Chapter 13 104
- Chapter 13 105 105
- 106 Chapter 13 106
- Configuring Port Clustering 108
- Chapter 13 108
- 10.Click Save & apply 108
- Clustering Parameters 109
- Accessing the Cluster Ports 109
- 110 Chapter 13 110
- System Administration 111
- 112 Chapter 14 112
- 114 Chapter 14 114
- 116 Chapter 14 116
- Command Line Interface 117
- Chapter 15 119 119
- File Name Description 120
- 122 Chapter 15 122
- 124 Chapter 16 124
- 126 Chapter 16 126
- Configure System Logging 127
- 128 Chapter 16 128
- 130 Chapter 16 130
- Viewing A Sniff Session 131
- 132 Chapter 16 132
- 134 Chapter 16 134
- 136 Chapter 16 136
- 124 for more information 137
- Hardware Test Menu 138
- Disaster Recovery 138
- Use the ESC key 139
- Chapter 16 140
- Hardware Information 141
- Hardware Specifications 142
- Chapter 17 142
- Attribute Value 142
- DB-25 Male Console Adapter 144
- Chapter 17 145 145
- RJ-45 Signal DB-9F Signal 145
- Cable Adapters 146
- RJ-45 Signal DB-25M Signal 146
- Chapter 17 147 147
- (Available but not included) 148
- Rack shown in illustration is 149
- 150 Chapter 17 150
- Certifications 151
- Safety Instructions 152
- Solaris Ready 154
- Chapter 18 154
- Index 155 155
- 156 Index 156
- 157 Index 157
- 90000301 158
Related products and manuals for Networking Digi CM
Networking Digi Edgeport 412 User Manual
(4 pages)
(4 pages)
Networking Digi ConnectPort X2 User Manual
(142 pages)
(142 pages)
Networking Digi Rabbit 5000 User Manual
(130 pages)
(130 pages)
Networking Digi Digi One EM Installation Guide
(168 pages)
(168 pages)
Networking Digi XStream-PKG-R RS-485 Manual
(60 pages)
(60 pages)
Networking Digi XPress User Manual
(18 pages)
(18 pages)
Networking Digi XPress Specifications
(143 pages)
(143 pages)
Networking Digi ConnectPort X4 User's Guide
(271 pages)
(271 pages)
Networking Digi XPress User Manual
(2 pages)
(2 pages)
Networking Digi XPress User Manual
(8 pages)
(8 pages)
Networking Digi 34 User Manual
(13 pages)
(13 pages)
Networking Digi CM User's Guide
(202 pages)
(202 pages)
Networking Digi SYNC/570i User Manual
(54 pages)
(54 pages)
Networking Digi 34 Specifications
(148 pages)
(148 pages)
Networking Digi M10 Specifications
(38 pages)
(38 pages)
Networking Digi Digi One EM User's Guide
(43 pages)
(43 pages)
Networking Digi 9P 9360/9750 User's Guide
(75 pages)
(75 pages)
© 2020, manymanuals.com. All rights reserved. | 0.965 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals