Digi DC-190 Installation Manual Page 44
- Page / 67
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
40 DC-190 Ultra Count Installation Manual
8.6.2 PC Output Data Format Without Header
The DC-190-to-PC output data format (without header) is specified using SPEC 12, with bit 0 set to 1. The
output data format is data-only. Each data block consists of Data and CR. The following is an illustration of the
output data format.
NOTES:
• CR must be added at the end of each data block.
• LF must be added at the end as a termination code of the transmission.
8.7 Data
Parts identification (ID) code is only sent when an ID code is called during the counting mode. The maximum is
32 characters. If the ID code is less than 32 characters, then the rest of the data will be filled with space characters
(20H). An example for parts code that equals 12 is shown in the diagram below.
Setpoint data is only sent when an ID code is called
during the counting mode. There are six setpoint data
to be sent: Setpoint 1 (F or G), Setpoint 2 (H),
Setpoint 3 (Q), Setpoint 4 (X), Setpoint 5 (U) and
Setpoint 6 (6).
Setpoint 1 (F) is defined as:
•Weight: variable length, maximum of five
digits and one decimal point.
Setpoint 1 (G) is defined as:
• Quantity: variable length with a maximum of
six digits.
NOTE: Only one F (Setpoint 1 – Weight) or one G
(Setpoint 1 – Quantity) is sent.
Setpoints 2 through 6 (H, Q, X, U, and 6) are data
with a format consisting of:
• Percentage: variable length, maximum of five
digits, and one decimal point, or
•Lower weight: variable length, maximum of
five digits, and one decimal point, or
•Lower quantity: variable length and a
maximum of seven digits.
Four combinations of Setpoint 1 and Setpoint 2 can be
sent as shown below:
Table 8-15 shows the result of printed data detailed
above:
Data CR Data CR ........ CR LF
Header Data
31
SP
SP SP SP SP SP SP SP SP SP CR
2
Setpoint 1 Setpoints 2 Setpoints 3–6
Quantity Percentage —
Upper quantity Lower quantity Lower quantity
Weight Percentage —
Upper weight Lower weight Lower weight
NOTE: Setpoints 2 through 6 must either increase or
decrease. The decimal point for weight must be correct.
Table 8-14. Setpoint Combinations
Printed
Descriptor
Description
GROSS
WEIGHT
Variable length, maximum of five digits
and one decimal point
NET WEIGHT Variable length, maximum of five digits
and one decimal point
UNIT WEIGHT Variable length, maximum of five digits
and one decimal point
TARE WEIGHT Variable length, maximum of five digits
and one decimal point
QUANTITY Variable length, maximum of seven digits
TOTAL
QUANTITY
Variable length, maximum of seven digits
when PRINT key is depressed
NOTE: Only one of “2” (QUANTITY) or “1” (TOTAL
QUANTITY) is sent at one time.
Table 8-15. Result of Printed Data
- Installation Manual 1
- Contents 3
- About This Manual 5
- 1.0 Introduction 5
- 1.4 DC-190 Console 8
- 1.4.2 DC-190 Keypad 9
- 2.0 Installation 10
- 2.3 Powering Up the DC-190 11
- TERMINAL 12
- BRACKET CAP SCREWS 14
- LOAD CELL CAP SCREWS 14
- PLATFORM ATTACH 15
- BRACKETS 15
- 3.0 Scale Setup 16
- 3.2 Serial Configurations 18
- 4.0 Configuration Settings 21
- * key (printer and PC) 23
- – Key in Add Mode 24
- 142 access code 25
- Digital Tare with Weight 27
- 5.0 Calibration 29
- 6.0 Scale Operations 30
- 6.2 Toggle Between Scales 31
- 6.4 Entering Unit Weights 31
- 6.6 Other Operations 33
- 7.0 Scale Programming 34
- 7.2 Item Code Maintenance 35
- 8.0 RS-232 Specifications 39
- 8.2 Eltron Printers 40
- 8.3 Epson Tape Printers 41
- 8.4 Epson Ticket Printers 42
- 8.5 Digi BCP-300 Printer 42
- 8.6 PC Output Data Formats 43
- Header Data 44
- SP SP SP SP SP SP SP SP SP CR 44
- 8.8 Status Data Byte 45
- 8.9 Bar Code Scanners 46
- 8.10 Header 46
- 8.11 Z Commands 47
- 9.1 Using HyperTerminal 48
- NET, OR TARE WEIGHT FIELDS 51
- 10.0 Appendix 54
- 10.3 Connector Pinouts 56
- POWER SUPPLY 57
- 10.4 Cable Wiring 58
- 10.5 Y-Cable Wiring Diagram 59
- 10.6 DC-190 Messages 60
- 10.9 Bar Code Board 63
- QuickScan 64
- 6000. See also SPECs 14 and 64
- 15 in Table 4-1 on page 50 64
- Appendix 61 65
- Appendix 63 67
Related products and manuals for Kitchen scales Digi DC-190
Kitchen scales Digi DC-530 Specifications
(62 pages)
(62 pages)
Kitchen scales Digi DC-190 User Manual
(6 pages)
(6 pages)
Kitchen scales Digi DC-180 Service Manual
(27 pages)
(27 pages)
Kitchen scales Digi DS-470 Specifications
(34 pages)
(34 pages)
Kitchen scales Digi DC-200 Service Manual
(122 pages)
(122 pages)
Kitchen scales Digi DC-788 Specifications
(61 pages)
(61 pages)
Kitchen scales Digi SM-300 User Manual
(6 pages)
(6 pages)
Kitchen scales Digi DC-530 User Manual
(4 pages)
(4 pages)
Kitchen scales Digi DC-190 Specifications
(66 pages)
(66 pages)
Kitchen scales Digi DC-100 Specifications
(43 pages)
(43 pages)
Kitchen scales Digi DC-300 User Manual
(4 pages)
(4 pages)
Kitchen scales Digi DC-300 Instruction Manual
(113 pages)
(113 pages)
Kitchen scales Digi DC-200 User Manual
(23 pages)
(23 pages)
Kitchen scales Digi DC-100 User Manual
(4 pages)
(4 pages)
Kitchen scales Digi SM-100 User Manual
(138 pages)
(138 pages)
Kitchen scales Digi SM-100 User Manual
(7 pages)
(7 pages)
(4 pages)Ss-cycle Power Tune Sport Exhaust System for 2014 Harley-Da manuály
Uživatelské manuály a uživatelské příručky pro Pro motocykly Ss-cycle Power Tune Sport Exhaust System for 2014 Harley-Da.
Poskytujeme 1 manuály pdf Ss-cycle Power Tune Sport Exhaust System for 2014 Harley-Da ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Comments to this Manuals