Digi DC-190 Specifications Page 1

73352 DC-190 OOOOppppeeeerrrraaaattttiiiioooonnnn MMMMaaaannnnuuuuaaaallllWhen Accuracy CountsCCCCoooouuuunnnnttttiiiinnnngggg SSSSccccaaaalll

1.7. DC190 CHARACTER CODE LIST (TERAOKA CODE)CODE CHARACTER CODE CHARACTER CODE CHARACTER00 SPACE 20 T 40 @01 A 21 U 41 !02 B 22 V 42 '&apos

2.0. SPECIFICATIONSThis section includes a detailed listing of all pertinent specifications and parameters for theDC-190 counting scales. The system

3.0. INSTALLATIONThis section provides the information required for installing this counting systemfor operation. The following steps accomplish inst

3.4. Sx Unlocking Procedure

4.0 OPERATION GUIDE IN WEIGHING MODE4.1 Tare Reduction :4.1.1 One Touch Tare Operation :All weights listed in these instructions are for example o

4.3.2. Unit Weight Operation by Key Entry : This following procedure is used if the unit weight isalready known.1 Display in the weighing mode2 Ent

4.5. Subtraction/Reduction Operation : When Spec32 bit1 (Auto Exit From Accumulation) is enabled.The Scale will automatically go back to Weight Mode a

4.8. Scale 1↔↔↔↔4 Operation :Display in the weighing modePressing [SCALE] key changes from Scale 1 to Scale 2.Pressing [SCALE] key changes from Scale

4.11. To Set New Item Code In Normal Operation:(Example: During Normal Weighing Mode, New Item Code No. 246 Is Required)This operation is valid only w

13 Press [NET/GROSS] Key

5.0. PROGRAMMING MODE:5.1.Item Programming (Program Mode):5 .1.1 Example 1 :To Set Unit Weight Into The Item Code No. 1231 Press [MODE] key to selec

5.1.3. Example 3 : Program Part No, Part Name Using T-C For Alpha/Numeric via DC190 keypad And Set Points12 Input 2 Digit Teraoka Code13 Enter Part N

5.2.2. Set Point Programming by Weight: %Set Point 1 : Weight (See Note Below) Set Point 2 : % Weight (See Note Below)Set bit 0 and 1 of Spec 7 to

5.2.4. Set Point Programming by Upper and Lower Limit of Weight:Set Point 1 : Weight (See Note Below) Set Point 2 : Weight (See Note Below)Set bit 0 a

5.3. Check Item Codes In Memory1. Press [MODE] key2. Press [CODE] key3. Press [+] key to check entered code4. Press [−−−−] key to check prior ente

6.0. MAINTENANCE MODE: 6.1. Scale Calibration :Prior to the calibration of the scale, please note that the SPEC settings corresponding to Minim

6.3. Spec 141 Setting: Spec 141(Customer Specifications) can be accessed from the weighing mode.Refer to pages 38 & 39 for a list of specs.1. Ent

6.5. DC-190 SPECIFICATION LIST ver.3.37Customer Specification : To enter this mode, press the following keysequence : [R][1][4][1] i.e. Numeric key

6.5. DC-190 Specification List ver.3.37 (continued)101 1 1 1RS-232CConnection(PC / Printer)0 : No1 : YesRS-232C(PC/PRN)Data Length0 :7 bits 1 :8 bitsR

6.5. DC-190 Specification List ver.3.37 (continued)Weight and Measures Specification : To enter this mode, enter the numeric keys 1,4,2 while pres

DC-190 SERIES OPERATING MANUALSECTION INDEX PAGE NUMBER1.0 GENERAL 5-101.1. Description 51.2. Appearance 61.3. Keyboard & Display Layout 61.4. Ind

6.5. DC-190 Specification List ver.3.37 (continued)Spec No. Bit 3 Bit 2 Bit 1 Bit 030 Load Cell Sensitivities Selection (mV/V) (Scale 1)Spc Min Max Sp

6.6. DC-190 RS-232 PORT SELECTION CHARTThe DC-190 has two R-232 ports for use with a force balance, printer, and or PC. Only two options are available

6.6. DC-190 RS-232 Specification6.6.1. PRINTER BCP-300 / PC6.6.1.1 GENERAL SPECIFICATIONBaud Rate : 1200 /2400 / 4800 / 9600 bps (Spec 10 bits 0 &

DC-190 RS-232 specification (continued)(i) HEADER WITH HEADER CODE (ii) HEADER WITH TITLEHeader Code is sent before the data to indicatetype of the da

DC-190 RS-232 specification (continued)(C) DATAID Code: Parts code is only sent when a ID Code is called during the counting mode. The maximum is 16

DC-190 RS-232 specification (continued)Status : The status data byte is as follows:Bit # If set to 1 If set to 0Bit 0 Positive weight Negative weightB

DC-190 RS-232 specification (continued)6.6.3.1. Connect To BCP-300DC190 can connect to BCP-300 printer.Set the following Specs:Baud Rate 9600 bps (Sp

DC-190 RS-232 SPECIFICATION (continued)6.6.3.3. CONNECT TO LP2622, 2742, 2722DC190 can connect to LP2622 printer.Set the following Specs:Baud Rate 96

DC-190 RS-232 SPECIFICATION (continued)6.6.3.6. Connect to EPSON TMU-295 using 8 pin “Din” connector.Without releaseBit 3 Bit 2 Bit 1 Bit 0Spec 3 0 0

DC-190 RS-232 specification (continued)6.6.4. Bar Code ScannerDC190 can support:RS232:Pen Scanner: ZB800- Can Support Up to 16 digitsPSC Laser Scanne

SECTION INDEX PAGE NUMBER5.0. PROGRAM MODE 19-235.1. Data setting Programming Id Code (200 Item Memory) 19-205.2. Set Point Programming 20-225.2.1. S

DC-190 RS-232 specification (continued)HEADERThe following type of header can be receivedHeader Code ASCII Code Data Header Code ASCII Code Data131Uni

DC-190 RS-232 specification (continued)6.6.5. FORCE BALANCEDC190 can support: OHAUS EXPLORER6.6.5.1. General SpecificationBaud Rate 1200 /2400 / 4800

6.6.5.3. RS232C Related Spec ListThe following R-141 spec must be set correctly in order for DC-190 to communicate with the Force BalanceSpec No. Bit

6.7. CONNECTOR MATRIX6.7.1.1. DC-90 Connector Matrix SX-1 Remote P/F DIN #1 DIN #2 “D” Set P

6.7.2. SETTING UP DC – 190When setting up a DC – 190 or adding a second channel, third channel or even aforce balance, it is necessary to assign a dif

The Spec Setting Below Is Not Acceptable As It Will Cause Scale ToLock Up In All 888888’s In The Weight Display. When This ConditionHas Occurred Acce

IF YOU ARE SETTING UP A…SINGLE PLATFORM SCALE$$$$ DIGI SX-L PLATFORM SEE PAGE 48%%%% OTHER DIGI PLATFORM SEE PAGE 48( YOU WILL NEED A PS-100 POWER SUP

THREE PLATFORM SCALE USING$$$$ DIGI SX-DUAL AND ONE OTHER PLATFORM SEE PAGE 51THREE PLATFORM SCALE USING%%%% DIGI SX-L AND TWO OTHER PLATFORMSDIGI OR

SCALE CALIBRATION$$$$ SCALE CALIBRATION PROCEDURE SEEPAGES 24%%%% VIEW INTERNAL COUNT SEE PAGE 24PLATFORM WIRING$$$$ REMOTE PLATFORM WIRING SEE PAGES

6.7.2.1. SETTING – UP SINGLE CHANNEL SCALEIF YOU ARE SETTING UP A SINGLE CHANNEL SCALE WITH ONE LOAD CELLTHIS IS THE WAY THE SPECS 16 & 17 SHOULD

1.0. GENERAL1.1. DescriptionThe DC-190 counting scale offers a practical solution to a full range ofprecision counting applications. There are a var

6.7.2.2. SETTING – UP TWO CHANNEL SCALE SX-D PLATFORMIF YOU ARE SETTING UP A TWO CHANNEL SCALE WITH PLATFORM CONTAINING TWO LOADCELLS BUILT –IN, THIS

6.7.2.3. SETTING – UP TWO CHANNEL SCALEIF YOU ARE SETTING UP A TWO CHANNEL SCALE WITH ONLY TWO PLATFORMS AND NO “Y”CABLE THIS IS THE WAY THE SPECS 16

6.7.2.4. THREE CHANNEL SCALEIF YOU ARE SETTING UP A THREE CHANNEL SCALE, USING AN SX-D AS SCALE 1 & 2 AND AREMOTE PLATFORM WITH NO “Y” CABLE THIS

IF YOU ARE SETTING UP A THREE CHANNEL SCALE WITH THREE PLATFORMS USING A“Y” CABLE THIS IS THE WAY THE SPECS 16 & 17 SHOULD BE SET.16 ∗∗∗∗

6.7.3. Connector Pin-Outs (Front View)SET POINT MINI DIN FEMALE 9 PIN “D” SUB FEMALE8 PIN DIN FEMALE 14 PIN AMPHENOL FEMALE

6.7.4. DC-190 Platform “Y” Cable Assembly

6.8. DC-190 Battery Installation Instructions1. Unplug Scale from power source.2. Remove platter.3. Remove platter support screws and platter support.

WARNING! Do Not Turn Scale Upside Down6.8. DC-190 Battery Installation Instructions (Continued)4. Remove case screws located on bottom of scale.5. Rem

6.8. DC-190 AC / Battery OperationThe DC-190 can be operated with AC power or with the optional internalbattery. The battery will automatically charg

6.9. DC-190 Assembly Procedure :Step 1. Attach mounting plate to bottom of SXPlatform with (4) chrome screws provided.Step 2 Place SX Platform on lev

1.2. Appearance1.3. Keyboard & Display Layout

6.10. DC-190 Pole Mounting InstructionsWARNING! Do Not Turn Scale Upside DownDC-190 Pole Mounting uses the underside bracket and leveling foot for sup

6.10. DC-190 Pole Mounting Instructions (continued)Fig.5 Fig. 6Use M4x 14 screws to attach Pull some load cell wireBracket to platform Through pole to

6.10. DC-190 Pole Mounting Instructions (continued)Fig. 9 Fig. 10DC-190 Console Remove all (3) truss head screwsFig. 11 Fig.12Remove rubber blocks a

6.10. DC-190 Pole Mounting Instructions (continued)Fig. 13 Fig. 14Plug load cell connector into Pull excess load cell cableDC-190 Console Down the po

6.10. DC-190 Pole Mounting Instructions (Continued)Fig.17When pole is mounted, re-assemble scale.Fig. 18Place scale on feet and adjust leveling foot

6.11. Shop Notes:

DC-190 Limited WarrantyRice Lake Weighing Systems (RLWS) warrants that all RLWS equipment and systems properly installed by aDistributor or Original E

1.4. Indicator LampsLAMP“ON”Zero When the gross weight is zero.Tare When tare weight is set.Gross When [Gross/Net] key is pressed.Insuff When the net

1.5. Key FunctionsKEY FUNCTIONSON/OFF For turning the machine ON and OFF.0 TO 9 Numeric Keys..Decimal Point.REZERO Used to reset the scale to zero. U

1.6. DC190 Message ListDC190 MESSAGE LISTMESSAGE CONTENTSACC Accuracy---Add XX Sampling quantity is InsufficientALL All MemoryC