Digi DC-190 Specifications download pdf (Page 50)

6.7.2.2. SETTING – UP TWO CHANNEL SCALE SX-D PLATFORM

IF YOU ARE SETTING UP A TWO CHANNEL SCALE WITH PLATFORM CONTAINING TWO LOAD

CELLS BUILT –IN, THIS IS THE WAY THE SPECS 16 & 17 SHOULD BE SET.

∗∗

Normally

Set

0 0 0 1

_ _ _ _

SCALE 1:

00: Internal Scale 1

01: Internal Scale 2

10: External Scale

11: Force Balance

SCALE 2:

00: Internal Scale 1

01: Internal Scale 2

10: External Scale

11: Force Balance

∗∗

Normally

Set

1 0 1 1

_ _ _ _

SCALE 3:

00: Internal Scale 1

01: Internal Scale 2

10: External Scale

11: Force Balance

SCALE 4:

00: Internal Scale 1

01: Internal Scale 2

10: External Scale

11: Force Balance

The SX-D Platform Would Be Plugged Into The SX-1 Load Cell Connector.

Using The SX-D Platform In Scale 1 SX-1 Connector No Power Supply Will Be Necessary As Power Will

Be Supplied By The Platform.

In This Case Other Specs That Will Need To Be Set Are As Follows:

Weight and Measures Specification: To enter this mode, enter the numeric keys 1,4,2 while pressing the Re-

zero Key. The Span Switch must be “ON” to enter this mode.

Spec No. Bit 3 Bit 2 Bit 1 Bit 0

_ _ _ _

Minimum Display ( Scale 1)

00 : 2 10 : 5

01 : 1 11 : 10 !!

Minimum Display (Scale 2)

00 : 2 10 : 5

01 : 1 11 : 10 !!

_ _ _ _

Weight Decimal Point Position (Scale 1)

000 : 00000 010 : 000.00 100 : 0.0000

001 : 0000.0 011 : 00.000 !!

_ _ _ _

Weight Decimal Point Position (Scale 2)

000 : 00000 010 : 000.00 100 : 0.0000

001 : 0000.0 011 : 00.000 !!

Normally

Set

0 0 1 1

Display Resolution

00 : 1/10,000 10 : 1/2,500

01 : 1/5,000 11 : Not Used

Zero Setting Range

00 : + Unlimited 10 : +- 10% FS

- 10% FS

01 : +- 2% FS 11 : Not Avail.

0 0 0 0

Scale Starting Method

0 : Automatic

1 : Manual

IR Mode

protected by

Span Switch

0 : No 1 : Yes

Scale Type

1 : Double

Scale !2

Gross Mode Available

0 : Yes

1 : No

1 0 1 1

Calibration Mode protected

by Span Switch

0 : Yes 1 : No

Battery Low

Lamp

0: Yes 1: No

Auto Exit from

Add Mode

0 : No 1 : Yes

External Load Cell (Scale 3)

0: No

0 _ _ _

Over Weight Mask at

0 : +1d

1 : +9d

Weight Decimal Point Position (Scale 3)

000 : 00000 010 : 000.00 100 : 0.0000

001 : 0000.0 011 : 00.000

_ _ 0 0

Minimum Display ( Scale 3)

00 : 2 10 : 5

01 : 1 11 : 10

A/D Board (For Scale 3)

00 : Normal

01 : Prevent from Small vibration / fast change in display

10 : Prevent from Medium vibration

11 : Prevent from Large slow change in display

To Select The Minimum Display And Decimal Location Divide Capacity By The Display Resolution Selected In

Spec23. !!

2 In This Case Scale 1 & 2 Will Be Turned On.

1 2 ... 45 46 47 48 49 50 51 52 53 54 55 ... 65 66

Comments to this Manuals

No comments

Digi DC-190 Specifications Page 50

Comments to this Manuals

Related products and manuals for Kitchen scales Digi DC-190