Digi PortServer TS 8 Setup Guide Page 105
- Page / 106
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
PortServer TS 8/16 Troubleshooting
17-15
Checking and Changing Port Configuration
Use this topic to ensure that PortServer TS 8/16 serial port configuration is correct. You can display
and change port configuration from either the command line or the web interface. This topic
addresses the command line only. For information regarding the web interface, access the port from
the web interface and then use the online help.
RealPort
•Specify set ports dev=rp to define a device type.
• Configure serial line attributes on the RealPort host.
• Configure flow control on the RealPort host.
Printer
• For most printers, specify set ports dev=prn.
• Use the set line command to configure serial line attributes that are consistent with peripheral
requirements.
• Use the set flow command to configure flow control attributes that are consistent with peripheral
requirements.
Incoming Modem
• For most incoming modem connections, specify set ports dev=min
• Use the set line command to configure serial line attributes that are consistent with peripheral
requirements.
• Use the set flow command to configure flow control attributes that are consistent with peripheral
requirements.
Outgoing Modem
• For most outgoing modem connections, specify set ports dev=mout.
• Use the set line command to configure serial line attributes that are consistent with peripheral
requirements.
• Use the set flow command to configure flow control attributes that are consistent with peripheral
requirements.
Two-way Modem
• For both incoming and outgoing modem connections, specify set ports dev=mio.
• Use the set line command to configure serial line attributes that are consistent with peripheral
requirements.
• Use the set flow command to configure flow control attributes that are consistent with peripheral
requirements.
Terminal
• For most terminal connections, specify set ports dev=term. Also, if you have configured
the port for autoconnection, ensure that the destination IP address and TCP port (dport) are cor-
rect.
• Use the set line command to configure serial line attributes that are consistent with peripheral
requirements.
• Use the set flow command to configure flow control attributes that are consistent with peripheral
requirements.
- PortServer TS 8/16 1
- Contents 3
- Chapter 1 Introduction 7
- Setup Overview 8
- About This Guide 9
- Supported Devices 9
- About Configuration Methods 11
- Configuration Prerequisites 12
- Configuring the IP Address 13
- Starting Point 15
- Procedure 15
- Manual Configuration Example 17
- About DHCP and RARP 17
- About RealPort 20
- Configuration Considerations 24
- Related Information 25
- Port Defaults 30
- About Computer Connections 31
- Tips on Configuring A Modem 34
- Before You Begin 36
- Chapter 8 Configuring PPP 37
- Introduction to Routing 44
- About RIP Routing Updates 45
- Configuring Static Routes 47
- Configuring Proxy ARP 49
- 9-8 Configuring Proxy ARP 50
- About Autoconnection 52
- In This Chapter 55
- About Console Management 56
- Example: SSH2 and Menu Access 57
- Default Access Restrictions 60
- Default Access 61
- Method 1 Autoconnection 61
- Method 2: Menus 61
- What is RADIUS? 62
- RADIUS Components 62
- RADIUS Table Key 62
- How RADIUS Works 63
- Issuing User Passwords 65
- Password Protection 66
- Using a Public Key 66
- Chapter 13 Configuring DNS 67
- About the Domain Name System 68
- Configuration Procedures 69
- Chapter 14 Configuring SNMP 71
- Configuration Example 73
- Prerequisite Task 77
- Chapter 15 Configuring Users 81
- About Configuring Users 82
- Common User Features 82
- Illustration 86
- Configuration 86
- Configuration Notes 86
- Introduction 92
- Procedures 92
- If ... Then 95
- Troubleshooting TFTP Problems 96
- Command Line Procedure 97
- Front Panel Procedure 97
- Pinging an IP Address 101
- Verifying the Network Cabling 102
- Digi Contact Information 106
Related products and manuals for Servers Digi PortServer TS 8
Servers Digi PortServer TS 8 User's Guide
(100 pages)
(100 pages)
Servers Digi DC-ES-8SB Setup Guide
(106 pages)
(106 pages)
Servers Digi LTS 32 Installation Guide
(191 pages)
(191 pages)
Servers Digi PortServer TS 8 Service Manual
(127 pages)
(127 pages)
Servers Digi TS 8 MEI User's Guide
(281 pages)
(281 pages)
Servers Digi DC-ES-8SB Setup Guide
(14 pages)
(14 pages)
© 2020, manymanuals.com. All rights reserved. | 0.528 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals