Digi ConnectPort X4 User's Guide Page 56
- Page / 271
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Configuration through the web interface
56
WiFi IP settings
The WiFi IP settings configure how the IP address of a Wi-Fi-enabled Digi device is obtained. It
has the same settings as the Ethernet IP settings page.
WiFi LAN settings
Digi devices with Wi-Fi (wireless LAN) capability contain a wireless network interface that may
be used to communicate to wireless networks using 802.11b8 technology. Contact your
administrator or consult wireless access point documentation for the settings required to setup the
wireless LAN configuration. Settings include:
Network name: The name of the wireless network to which the wireless device should
connect. In situations with multiple wireless networks, this setting allows the device to
connect to and associate with a specific network. The network name is referred to as the
SSID (service set identifier). If the network name is left blank, the device will search for
wireless networks and connect to the first available network. This is useful if a specific
network name does not need to be used as the device will select the first available
network.
Connection method: The type of connection method this device uses to communicate
on wireless networks. Choose from:
– Connect to any available wireless network: Use this setting to allow the device to
access any network. The device can either access point networks or peer-to-peer
wireless networks.
– Connect to access point (infrastructure) networks only: Use this setting if the
wireless network that this device needs to connect to is composed of wireless access
points. This is typically the most popular method for connecting to wireless networks.
– Connect to peer-to-peer (ad-hoc) networks only: Use this setting if all devices on the
wireless network connect to and communicate with each other. This is known as peer-
to-peer in that there is no central server or access point. Each system communicates
directly with each other system.
Country: The country in which this wireless device is being used. The channel settings
are restricted to the legal set for the selected country.
Channel: The frequency channel that the wireless radio will use. Select Auto-Scan to
have the device scan all frequencies until it finds one with an available access point or
wireless network it can join.
Transmit Power: The transmit power level in dBm.
Enable Short Preamble: Enables transmission of wireless frames using short
preambles. If Short Preamble is supported in the wireless network, enabling it can boost
overall throughput.
- ConnectPort 1
- X Family 1
- User’s Guide 1
- Contents 3
- About this guide 6
- Digi contact information 7
- Introduction 8
- X products 9
- Features 10
- IP protocol support 11
- Provisioning wizard 15
- Digi SureLink™ 15
- Mobile/Cellular protocols 15
- RealPort software 16
- Modem emulation 17
- Encryption 18
- Configuration management 19
- Customization capabilities 19
- Network services 20
- Network/serial clients 22
- Configuration capabilities 23
- Configuration interfaces 24
- Digi Device Discovery utility 25
- Device Manager™ interface 26
- Web interface 28
- Command-line interface 29
- Device Manager 31
- Hardware 33
- Connector pinouts 34
- 4 analog I/O 37
- 4 digital I/O 37
- Cable fittings 39
- SIM card slots 40
- Power cable fitting 41
- Optional Ethernet hub feature 42
- Configuration 43
- IP address assignment 44
- Open the web interface 47
- Discover devices 48
- The Home page 49
- Ethernet IP settings 55
- WiFi IP settings 56
- WiFi LAN settings 56
- WiFi security settings 57
- WEP Keys 58
- DHCP server settings 60
- Network services settings 64
- Dynamic DNS update settings 67
- IP filtering settings 70
- IP forwarding settings 71
- IP Network Failover settings 74
- Socket tunnel settings 78
- General Security Settings 80
- Miscellaneous Settings 80
- Local Endpoint Type: 81
- VPN Mode: 81
- Identity settings 81
- Local Endpoint: 82
- Pre-Shared Key Settings 83
- ISAKMP Phase 1 Settings 84
- Cellular 86
- Data Network 86
- Internet 86
- Remote Site HQ 86
- IP pass-through settings 88
- Host List settings 91
- Advanced network settings 93
- Mobile (cellular) settings 99
- Mobile Settings 101
- 5 Provisioning complete 104
- SIM Selection settings 105
- GPS settings 106
- Advanced Settings 107
- Digi SureLink™ settings 109
- Update PRL settings 113
- Enable 116
- Password 116
- Notes for the table: 118
- Supported character set 119
- WiMAX settings 125
- Network Connection 126
- XBee network settings 127
- Basic Settings 129
- Device Status 129
- Device Operations 130
- Gateway firmware updates 132
- OTA firmware updates 133
- .EXT value in 139
- File type 139
- Serial port settings 141
- RealPort profile 142
- Console Management profile 142
- TCP Sockets profile 143
- When the TCP 143
- UDP Sockets profile 144
- Serial Bridge profile 144
- Local Configuration profile 144
- Modem Emulation profile 145
- Industrial Automation profile 145
- GPS Profile 145
- Custom Profile 145
- Basic serial settings 146
- Advanced serial settings 147
- Camera settings 150
- Alarm notification settings 151
- Alarm conditions 152
- Alarm configuration 153
- Enable and Disable Alarms 154
- System settings 155
- Authentication failure 161
- Cold start 161
- Link up 161
- Device Cloud settings 163
- Connection settings 164
- Mobile (Cellular) Settings: 169
- 4 Click Apply 171
- Users settings 172
- Caution 173
- Password authentication 174
- Add users 176
- User access settings 176
- User permissions settings 177
- 3 Click on User Permissions 178
- 5 Click Apply 178
- Position - GPS support 180
- Applications 182
- Digi device 184
- Digi device and click Delete 184
- RealPort Settings 187
- Ekahau Client™ 188
- Device Descriptors: 189
- Access the command line 191
- Monitoring and management 195
- Display system information 197
- Serial port information 198
- Network statistics 200
- ICMP statistics 202
- WiFi LAN statistics 203
- Device Cloud status 215
- Position/GPS statistics 215
- XBee Network 216
- Watchport Sensor statistics 218
- SureLink statistics 219
- Diagnostics 220
- Manage serial ports 221
- Manage connections 221
- Event logging 222
- Manage network services 223
- Device administration 230
- File management 231
- Secure Shell (SSH) Hostkeys 243
- Prerequisites 245
- Using the boot command 246
- Connector 247
- ConnectPort X4 H 248
- Reset button 248
- Reboot the Digi device 250
- Specifications and 252
- ConnectPort X2 specifications 253
- 4.5 in (11.4 cm) 254
- ConnectPort X4 specifications 255
- Hardware specifications 256
- Wireless networking features 257
- Infrastructure Mode 258
- Ad-Hoc Mode 258
- FCC Part 15 Class B 259
- ((( ))) 262
- ConnectPort X4 S2 2G Term 263
- ConnectPort X4 H 263
- Troubleshooting 265
- System status LEDs 266
- 1: signal strength low/weak 267
- ConnectPort X4 - Top 268
- ConnectPort X4 - Front panel 268
- ONNECT ORT 269
Related products and manuals for Networking Digi ConnectPort X4
Networking Digi XPress User Manual
(2 pages)
(2 pages)
Networking Digi XPress User Manual
(8 pages)
(8 pages)
Networking Digi 34 User Manual
(13 pages)
(13 pages)
Networking Digi CM User's Guide
(202 pages)
(202 pages)
Networking Digi SYNC/570i User Manual
(54 pages)
(54 pages)
Networking Digi 34 Specifications
(148 pages)
(148 pages)
Networking Digi M10 Specifications
(38 pages)
(38 pages)
Networking Digi Digi One EM User's Guide
(43 pages)
(43 pages)
Networking Digi 9P 9360/9750 User's Guide
(75 pages)
(75 pages)
Networking Digi CM User Manual
(1 pages)
(1 pages)
Networking Digi Rabbit 5000 User Manual
(119 pages)
(119 pages)
Networking Digi LTS 32 User's Guide
(150 pages)
(150 pages)
Networking Digi ConnectPort X4 User Manual
(37 pages)
(37 pages)
© 2020, manymanuals.com. All rights reserved. | 0.332 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals